How to Replace the Vibrator of iPhone 6S Plus Recommend

Posted by 2018-04-09 13:51:34 Tutorials 0 Comments

How to Replace the Vibrator of iPhone 6S Plus

1.Repairing the device by yourselves is likely to cause breakdown or data loss. So make sure that you backup your data before repairing. There are two ways to backup via iTunes. The first way is to connect your phone to PC. Open Itunes to pair your phone and start to backup. The another way is to make sure that your phone has connected to Wi-Fi. Open Settings-iCloud-Storage and start to backup. 
2.Relax and be patient. Put the screws and fittings in a container or in the flat object.
3.Attention
(1)Use screwdriver correctly, or it will cause screw loosed or phone damaged.
(2)You must use magnetic screw pasting, which can help you to recognize the position of screw. Wrong position will damage your phone.
(3)Please be careful when you dismount and install because the flex cable is fragile.
4. Power off your iPhone. If the screen is abnormal, please press the power button and home button together and loosen when you see the notice of powering off.


5.Remove the two pentagonal screws that next to the Lightning connector.


6.Use hair dryer or blower gun to heat the edge of phone.


7.Apply a suction cup to the screen that over the home button. If the screen is broken, please stick a tape on the screen. Pull up on the suction cup.


8.Use your fingernail to reate a slight gap.


9. Put the triangular plate into the gap.


10.Widen the gap along the side.


11.Open the screen slowly.Don't pull it up violently, as it is connected at the top by cables that may break if stretched.


12.To reduce damage, please cut power. Use cross screwdriver to remove the two Phillips screws.


13.Use spudger to remove the battery connector bracket. 


14.Remove the Phillips screws on the EMI shielding of flat cables and then remove metal shielding plate.


15.To prevent installing screws incorrectly, I advise tyro to use Memory Cushion.


16.Use the tip to remove flat cable. 


17.Then seperate it.


18.Use cross screwsdriver to remove the screws on the protective interface metal and remove the protective interface metal.


19.Use cross screwsdriver to remove the screws of vibrator.


20.Use spudger to remove the cables connector of vibrator.


21.Remove the vibrator.


22.Install new vibrator.


23.Buckle down the cables connector of vibrator.


24.Install the fixed screws of vibrator using cross screwdriver.


25.Install the protective interface metal.


26.Install the screws of protective interface metal.


27.Clean the remaining of tapes.


28.Stick the waterproof.Peel away the protective film.


29.Install the screen and connect the flat cable. If you connect correctly, you can hear slight sound. If not, try again.


30.Connect the battery cables.


31.Put down your phone and check if it is normal.
Check these function: display ,touch, camera, receiver, sensitization, speaker, volume button, record, power button. If all is well, power off. If not, remove the screen and check again.


32.Install EMI and the screws.


33.Install the battery bracket and screws.


34.Close the screen , pull along with the arrow and buckle down. If you cannot close normally, please check if there are something inside or if you didn't install correctly.


35.Install the last two pentagonal screws.


36.Finish. Power on your phone and check it.

Leave A Reply

Recommended Articles

How to Replace the Speaker of iPad Air 2

Repairing the device by yourselves is likely to cause breakdown or data loss. So make sure that you backup your data before repairing. There are two ways to backup via iTunes. The first way is to connect your phone to PC. Open iTunes to pair your phone and start to backup. The another way is to make sure that your phone has connected to Wi-Fi. Open Settings-iCloud-Storage and start to backup. 
2018-04-14 Read More

Leak Photos of Gold iPhone X

Recently, the FCC(Federal Communication Commission) showed leak photos of gold iPhone X.  The American Smartphone manufacturer should offer the products information to FCC before releasing new products. The application date of these photos is last September,which meant Apple offer an gold iPhone X that wasn’t released.
2018-04-14 Read More

How to Save Battery Consumption After Upgrading iOS11

Recently, some iPhone users said that after their iPhone(the models under iPhone 8 ) upgraded iOS11, the battery consumed faster. According to the survey from an information resource, the battery consumption speed of iOS 11 is twice faster than iOS 10. The average using time of iOS 10 is 240 minutes while the iOS 11 is 96 minutes.
2018-04-12 Read More

Apple Released Red iPhone 8 and Red Leather Folio Case for iPhone X 

Apple released Red iPhone 8 and iPhone 8 Plus. Besides, it released a red leather folio case for iPhone X. The features of red iPhone 8/8 Plus are the same as the common iPhone 8. The red iPhone 8 also takes the design of glass backboard and white “Apple” logo. It is worth mentioning that red iPhone 8 takes the aluminum metal middle bezel with same color.
2018-04-12 Read More