How to Replace the iPad Air 2 Volume Control Cables Recommend

Posted by 2018-04-14 14:38:19 Tutorials 0 Comments

How to Replace the iPad Air 2 Volume Control Cables


1.Repairing the device by yourselves is likely to cause breakdown or data loss. So make sure that you backup your data before repairing. There are two ways to backup via iTunes. The first way is to connect your phone to PC. Open Itunes to pair your phone and start to backup. The another way is to make sure that your phone has connected to Wi-Fi. Open Settings-iCloud-Storage and start to backup. 
2.Relax and be patient. Put the screws and fittings in a container or in the flat object.
3.Power off your device.


4.Use hair dryer or blower gun to heat the edge of device evenly about 2 to 5 minutes. Heating lets tape become softer. The temperature of blower gun is 150 Celsius degree. 


5.Put the tool into the edge of screen. Do not be violent. Open a gap and gash along the gap slowly. Please be careful of the front-camera.


6.To avoid pasting again, you can insert some objects such as triangle slice or phone cards. The tapes will be cooler due to the long time. So you can heat again.


7.Be careful of the home button and the flat cables.


8.After gashing, open the screen lightly with the angle of 60 degree.


9.Use cross screwdriver to remove the screws on the shielding case.


10.Remove the shielding case.


11.Open the cables connector.


12.Seperate the screen carefully.


13.Use cross screwdriver to remove these four screws.


14.Remove the protective cables metal plate.


15.Open the cables connector of back camera.


16.Pry the back camera lens and let it loose.


17.Remove the back camera lens. After removing, please keep another fixed lens clean.


18.Use cross screwdriver to remove the screws on the volume flex cables shielding case.


19.Remove the shielding case of volume control cables connector.


20.Remove the volume control cables connector.


21.Use cross screwdriver to remove the fixed screws on the volume button metal.


22.Pry the volume control cables and let it loose.


23.Remove the volume button metal.


24.Pry it using spudger.


25.Seperate the metal and flex cables.


26.Peel away the protective film on the new cables and stick the new cables on the metal.


27.Stick it according to the former position.


28.Stick the metal.


29.Install the four screws on the metal.


30.Check if the button can be used normally.


31.Buckle down the volume control cables connector.


32.Install the volume control cables shielding case.


33.Use cross screwdriver to install the screws on th shielding case.


34.Stick the control cables.


35.Install the back-camera. Clean the lens using small hairbrush. If there is smudge, you can sprinkle 530 to clean it.


36.Install the back camera. Aim at the right position and then stick it. Please be careful and don’t let dust fall on the lens.


37.Buckle down the cables connector. If you do it correctly, you can hear slight sound. If not, try again.


38.Install the protective cables metal.


39.Use the cross screwdriver to install the four screws.


40.Stick the tape on the new screen.


41.This picture is the position of tape.


42.Remove the remaining tape.


43.Take the screen and align at the edge of middle bezel.


44.Buckle down these three cables. If you do it correctly, you can hear slight sound. If not, try again.


45.Close the screen slowly.


46.Power off the device. Choose any desktop icon. Long press the icon and the icon will become shaking. Drag the icon and slide the icon to check it there is any problem of touching fuction.


47.After testing, tap the Settings-Touch ID and Password and then add fingerprint to check if the finger can be printed normally. If not, install the flat cables again.


48.Check the home button, display screen,music playing and other functions.


49.After checking, power off.


50.Remove these cables. 


51.Peel away the protective film of tape.


52.Before installing, you can smear the B-7000 glu on the edge of middle bezel. It helps stick firmly.


53.Buckle down the cables connector.


54.Install the shielding case in the right position.


55.Install these three screws.


56.When installing the first screw, don’t put it too tight. Because you can adjust the position of shielding case. 


57.Close it. You can also check the functions before closing. 


58.Finished.

Leave A Reply

Recommended Articles

How to Replace the Speaker of iPad Air 2

Repairing the device by yourselves is likely to cause breakdown or data loss. So make sure that you backup your data before repairing. There are two ways to backup via iTunes. The first way is to connect your phone to PC. Open iTunes to pair your phone and start to backup. The another way is to make sure that your phone has connected to Wi-Fi. Open Settings-iCloud-Storage and start to backup. 
2018-04-14 Read More

Leak Photos of Gold iPhone X

Recently, the FCC(Federal Communication Commission) showed leak photos of gold iPhone X.  The American Smartphone manufacturer should offer the products information to FCC before releasing new products. The application date of these photos is last September,which meant Apple offer an gold iPhone X that wasn’t released.
2018-04-14 Read More

How to Save Battery Consumption After Upgrading iOS11

Recently, some iPhone users said that after their iPhone(the models under iPhone 8 ) upgraded iOS11, the battery consumed faster. According to the survey from an information resource, the battery consumption speed of iOS 11 is twice faster than iOS 10. The average using time of iOS 10 is 240 minutes while the iOS 11 is 96 minutes.
2018-04-12 Read More

Apple Released Red iPhone 8 and Red Leather Folio Case for iPhone X 

Apple released Red iPhone 8 and iPhone 8 Plus. Besides, it released a red leather folio case for iPhone X. The features of red iPhone 8/8 Plus are the same as the common iPhone 8. The red iPhone 8 also takes the design of glass backboard and white “Apple” logo. It is worth mentioning that red iPhone 8 takes the aluminum metal middle bezel with same color.
2018-04-12 Read More